ABB RDNA-01 Manuale Utente Pagina 263
- Pagina / 320
- Indice
- SEGNALIBRI
Valutato. / 5. Basato su recensioni clienti
ACS550-01/U1 User’s Manual 263
Diagnostics
Alarm codes (Basic Control Panel)
The Basic Control Panel indicates control panel alarms with a code, A5xxx. The
following table lists the alarm codes and descriptions.
2023 EMERGENCY
STOP
Emergency stop activated.
2024
ENCODER ERROR The drive is not detecting a valid encoder signal. Check for and
correct:
• Encoder presence and proper connection (reverse wired, loose
connection,or short circuit).
• Voltage logic levels are outside of the specified range.
• A working and properly connected Pulse Encoder Interface Module,
OTAC-01.
• Wrong value entered in parameter 5001
PULSE NR. A wrong value
will only be detected if the error is such that the calculated slip is
greater than 4 times the rated slip of the motor.
• Encoder is not being used, but parameter 5002
ENCODER ENABLE =
1(
ENABLE).
2025
FIRST START Signals that a the drive is performing a First Start evaluation of motor
characteristics. This is normal the first time the motor is run after motor
parameters are entered or changed. See parameter 9910 ID RUN for a
description of motor models.
2026
RESERVED Not used.
2027 USER LOAD
CURVE
This alarm warns that the condition defined by parameter 3701 USER
LOAD C MODE has been valid longer than half of the time defined by
3703
USER LOAD C TIME.
2028 START DELAY Shown during the Start delay. See parameter 2113 START DELAY.
Note 1. Even when the relay output is configured to indicate alarm conditions (e.g. parameter
1401
RELAY OUTPUT 1 = 5 (ALARM) or 16 (FLT/ALARM)), this alarm is not indicated by a relay
output.
Code Description
5001 Drive is not responding.
5002 The communication profile is incompatible with the drive.
5010 The panel’s parameter backup file is corrupted.
5011 Drive is controlled from another source.
5012 Rotation direction is locked.
5013 Button is disabled, because start is inhibited.
5014 Button is disabled, because drive is faulted.
5015 Button is disabled, because local mode lock is on.
5018 Parameter default value can’t be found.
5019 Writing a non-zero value is prohibited (can only write a zero value).
5020 Group or parameter does not exist or parameter value is inconsistent.
5021 Group or parameter is hidden.
5022 Group or parameter is write protected.
5023 Modification is not allowed while the drive is running.
Alarm
code
Display Description
- User’s Manual 1
- ACS550-01 Drives (0.75 1
- ACS550-U1 Drives (1 1
- List of related manuals 2
- ACS550-01/U1 Drives 3
- 0.75…160 kW 3
- 1…200 hp 3
- Use of warnings and notes 5
- 6 ACS550-01/U1 User’s Manual 6
- 8 ACS550-01/U1 User’s Manual 8
- ACS550-01/U1 User’s Manual 9 9
- 10 ACS550-01/U1 User’s Manual 10
- Table of contents 10
- Installation 11
- Preparing for installation 12
- ACS550-01/U1 User’s Manual 13 13
- ACS550-01-08A8-4+J404+… 13
- 14 ACS550-01/U1 User’s Manual 14
- ACS550-01/U1 User’s Manual 15 15
- Installing the drive 16
- ACS550-01/U1 User’s Manual 17 17
- 18 ACS550-01/U1 User’s Manual 18
- ACS550-01/U1 User’s Manual 19 19
- 20 ACS550-01/U1 User’s Manual 20
- ACS550-01/U1 User’s Manual 21 21
- R5 and R6 22
- ACS550-01/U1 User’s Manual 23 23
- Control terminals table 24
- ACS550-01/U1 User’s Manual 25 25
- 26 ACS550-01/U1 User’s Manual 26
- ACS550-01/U1 User’s Manual 27 27
- 28 ACS550-01/U1 User’s Manual 28
- ACS550-01/U1 User’s Manual 29 29
- 30 ACS550-01/U1 User’s Manual 30
- Check installation 31
- 32 ACS550-01/U1 User’s Manual 32
- How to start up the drive 33
- 34 ACS550-01/U1 User’s Manual 34
- ABB Motors 35
- 36 ACS550-01/U1 User’s Manual 36
- ACS550-01/U1 User’s Manual 37 37
- 38 ACS550-01/U1 User’s Manual 38
- ACS550-01/U1 User’s Manual 39 39
- REQUEST) 40
- ACS550-01/U1 User’s Manual 41 41
- 42 ACS550-01/U1 User’s Manual 42
- Control panels 43
- 1200 RPM 44
- 405 dm3/s 44
- ACS550-01/U1 User’s Manual 45 45
- 46 ACS550-01/U1 User’s Manual 46
- How to get help 47
- 48 ACS550-01/U1 User’s Manual 48
- ACS550-01/U1 User’s Manual 49 49
- 50 ACS550-01/U1 User’s Manual 50
- PARAMETERS 51
- ASSISTANTS 51
- CHANGED PAR 51
- ABB STANDARD 51
- 52 ACS550-01/U1 User’s Manual 52
- 54 ACS550-01/U1 User’s Manual 54
- ACS550-01/U1 User’s Manual 55 55
- 19.03.05 59
- 60 ACS550-01/U1 User’s Manual 60
- Basic Control Panel 64
- ACS550-01/U1 User’s Manual 65 65
- 66 ACS550-01/U1 User’s Manual 66
- ACS550-01/U1 User’s Manual 67 67
- Reference mode 68
- ACS550-01/U1 User’s Manual 69 69
- 70 ACS550-01/U1 User’s Manual 70
- ACS550-01/U1 User’s Manual 71 71
- 72 ACS550-01/U1 User’s Manual 72
- Application macros 73
- ABB Standard macro 74
- 3-wire macro 75
- Alternate macro 76
- ALTERNATE) 76
- Motor Potentiometer macro 77
- MOTOR POT) 77
- Hand-Auto macro 78
- HAND/AUTO) 78
- PID Control macro 79
- PID CONTROL) 79
- PFC macro 80
- PFC CONTROL) 80
- Torque Control macro 81
- TORQUE CTRL) 81
- 82 ACS550-01/U1 User’s Manual 82
- User parameter sets 83
- USER S1 SAVE) 83
- USER S1 LOAD) 83
- 84 ACS550-01/U1 User’s Manual 84
- ACS550-U1 85
- 86 ACS550-01/U1 User’s Manual 86
- 88 ACS550-01/U1 User’s Manual 88
- ACS550-01/U1 User’s Manual 89 89
- 90 ACS550-01/U1 User’s Manual 90
- ACS550-01/U1 User’s Manual 91 91
- 92 ACS550-01/U1 User’s Manual 92
- ACS550-01/U1 User’s Manual 93 93
- 94 ACS550-01/U1 User’s Manual 94
- ACS550-01/U1 User’s Manual 95 95
- 96 ACS550-01/U1 User’s Manual 96
- ACS550-01/U1 User’s Manual 97 97
- 98 ACS550-01/U1 User’s Manual 98
- ACS550-01/U1 User’s Manual 99 99
- Parameters 100
- Group 99: START-UP DATA 102
- • set up the drive 102
- • enter motor information 102
- Group 01: OPERATING DATA 104
- Group 03: FB ACTUAL SIGNALS 108
- Group 04: FAULT HISTORY 110
- REF1 and REF2 113
- Group 13: ANALOG INPUTS 119
- Group 14: RELAY OUTPUTS 120
- Group 16: SYSTEM CONTROLS 125
- Group 20: LIMITS 129
- Group 21: START/STOP 132
- Group 22: ACCEL/DECEL 135
- Group 23: SPEED CONTROL 137
- Group 24: TORQUE CONTROL 139
- Group 25: CRITICAL SPEEDS 140
- Group 26: MOTOR CONTROL 141
- Group 29: MAINTENANCE TRIG 143
- Group 30: FAULT FUNCTIONS 144
- Group 31: AUTOMATIC RESET 148
- Group 32: SUPERVISION 149
- Group 33: INFORMATION 151
- Group 34: PANEL DISPLAY 152
- FAULT FUNCTIONS 156
- Group 37: USER LOAD CURVE 162
- PID 1 PARAM SET 173
- SAVED KWH, 0175 SAVED MWH 176
- Group 51: EXT COMM MODULE 178
- Group 52: PANEL COMM 180
- Group 53: EFB PROTOCOL 181
- Group 98: OPTIONS 198
- Embedded fieldbus 199
- Planning 200
- Communication set-up – EFB 201
- COMM PROT SEL = 201
- STD MODBUS) 201
- PID control setpoint source 206
- Communication fault 206
- Feedback from the drive – EFB 207
- Diagnostics – EFB 208
- COMM FAULT TIME 210
- ACTUAL VALUES and are: 218
- ABB Drives profile 220
- DCU Profile 221
- Status Word 222
- The contents of the 222
- DCU profile 224
- ABB DRV LIM 226
- CONTROL WORD (CW) 227
- Fieldbus adapter 231
- Communication set-up – FBA 235
- COMM PROT SEL. Set 9802 235
- EXT FBA) 235
- Feedback from the drive – FBA 238
- Diagnostics – FBA 239
- CONTROL WORD is 242
- STATUS WORD (SW) bits 245
- Diagnostics 253
- ALARM 2008 254
- Fault resetting 259
- Correcting alarms 260
- Alarm listing 261
- Maintenance 265
- Main fan replacement 266
- Capacitors 269
- Control panel 269
- Technical data 271
- Ratings, 380…480 V drives 272
- Input power connections 275
- Motor connections 283
- EARTH FAULT 286
- Brake components 289
- DISABLE)] 292
- Control connections 293
- Efficiency 294
- Air flow, 208…240 V drives 295
- Air flow, 380…480 V drives 295
- Air flow, 500…600 V drives 296
- Dimensions and weights 297
- Outside dimensions 298
- Degrees of protection 300
- Ambient conditions 300
- Materials 301
- Applicable standards 303
- CE marking 303
- C-Tick marking 303
- UL/CSA markings 304
- MOT THERM PROT) 304
- MOT THERM RATE) 304
- Product protection in the USA 306
- Numerics 307
- Further information 319
- EFFECTIVE: 2009-07-07 320
Prodotti e manuali riguardandi no ABB RDNA-01
no ABB SPA-ZC 400 Manuale di Servizio
(76 pagine)
(76 pagine)
no ABB SPA-ZC 402 Manuale di Servizio
(88 pagine)
(88 pagine)
no ABB Tina 7A Manuale di Servizio
(56 pagine)
(56 pagine)
no ABB RDNA-01 Manuale Utente
(348 pagine)
(348 pagine)
no ABB Tina 7A Manuale di Servizio
(12 pagine)
(12 pagine)
no ABB FENA-01 Manuale Utente
(34 pagine)
(34 pagine)
no ABB FPBA-01 Specifiche
(21 pagine)
(21 pagine)
no ABB AW400 Series Manuale Utente
(8 pagine)
(8 pagine)
no ABB FENA-21 Manuale Utente
(46 pagine)
(46 pagine)
no ABB RECA-01 Manuale Utente
(6 pagine)
(6 pagine)
no ABB FDNA-01 Manuale Utente
(460 pagine)
(460 pagine)
no ABB RDNA-01 Manuale Utente
(330 pagine)
(330 pagine)
no ABB Tina 7A Manuale di Servizio
(62 pagine)
(62 pagine)
no ABB RDNA-01 Manuale Utente
(302 pagine)
(302 pagine)
no ABB Tina 7A Manuale Utente
(44 pagine)
(44 pagine)
no ABB ML82PH Manuale Utente
(29 pagine)
(29 pagine)
© 2020, manymanuals.it. Tutti i diritti riservati | 0.053 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commenti su questo manuale